DT Receiver - Rx43d-1-v502 - Programming


PRODUCT: Rx43d-1-v5
INSTRUCTIONS: v5.0.2

1. PROGRAMMING APPROACH:


Step 2

Step 3

Steps 4-8

1. Switch Transmitter on.
2. Hold left/right sticks (Ch2/4) in towards middle of Tx.
3. Switch Receiver on and wait for the Led to flicker very fast.
4. Center all sticks.
5. The led flashes the setting for the first 'Level' (eg: 1-flash = H outputs).
6. Yes = push the Ch3 (Elevator) stick forward (to top of Tx) to accept this and advance to next Level.
7. No = pull the Ch3 (Elevator) stick back (to bottom of Tx) to see next option for same Level.
8. Continue through all Levels until Led comes on solid.
9. Settings are saved automatically at the end so switch off at any time to abort.
10. Say 'yes' to every item to just see what is currently set.

Changing 'P2' from Ch4 to Ch5.
Level 1: 3-flash = P
Level 2: 2-flash = P2
Level 3: 1-flash = Servo
Level 4: 5-flash = Ch5


2. PROGRAMMING OPTIONS:

Level 1
'H', 'F', 'P' or 'Other'
Level 2
Output number
Level 3
Output type
Level 4
Channel number
Level 5
Other choices
Default Information
1 flash = 'H' outputs 1 flash = H1 1 flash = 'Half stick' control
(center off)
1-7 flash = Channel 1-7 1113 1/2 stick forward, 1/2 stick back, middle off
Set 'Arming' position to 'middle'

1 flash = 'H' outputs 1 flash = H1 3 flash = 'Full stick' control
(low off)
1-7 flash = Primary Ch 1-7 1-7 flash = Direction Ch 1-7 Low stick 0%, full stick 100%
'Direction' channel toggles forward/reverse
(when 'Primary' channel is 0%)
Set 'Arming' position to 'low'

2 flash = 'F' outputs 1-2 flash = F1-2 1 flash = Normal (low off) 1-7 flash = Channel 1-7 Low stick 0%, full stick 100%

2 flash = 'F' outputs 1 flash = F1 2 flash = 2 channel mix
1-7 flash = 1st Ch 1-7 1 flash = 0% mix
2 flash = 12.5% mix
3 flash = 25% mix
4 flash = 50% mix
5 flash = 100% mix
F1/F2 used as a pair
(eg: Ch1 throttle)
2 flash = 'F' outputs 2 flash = F2 2 flash = 2 channel mix
1-7 flash = 2nd Ch 1-7 (eg: Ch2 steering)

2 flash = 'F' outputs 1 flash = F1
2 flash = F2
3 flash = Muscle wire /
2-coil actuator /
2 switches /
ADD1
1-7 flash = Channel 1-7 2132
2232
F1/F2 used as a pair for steering; or
Left stick gives Switch action on F1 (eg: light)
Right stick gives Switch action on F2 (eg: light)

3 flash = 'P' outputs 1-8 flash = P1-8 1 flash = Servo 1-7 flash = Channel 1-7 3112 1-8 servos no mix

3 flash = 'P' outputs 1 flash = P1 2 flash = Servo 2 channel mix
1-7 flash = 1st Ch 1-7 1 flash = 0% mix
2 flash = 12.5% mix
3 flash = 25% mix
4 flash = 50% mix
5 flash = 100% mix
P1/P2 used as a pair
3 flash = 'P' outputs 2 flash = P2 2 flash = Servo 2 channel mix
1-7 flash = 2nd Ch 1-7 1 flash = not reversed
2 flash = reversed
P1/P2 used as a pair

3 flash = 'P' outputs 1-8 flash = P1-8 3 flash = Brake or Reverse led 1-7 flash = Activating Ch
1 flash = Brake
2 flash = Reverse
37331
38332
1 channel controls 2 outputs

3 flash = 'P' outputs 1-8 flash = P1-8 4 flash = Left indicator led
5 flash = Right indicator led
6 flash = Flashing led (0.5s)
1-7 flash = Activating Ch 1-7 flash = Steering Ch 1-7 32442
33542
3464
1 'activating' channel controls 3 outputs
1 'steering' channel cancels left/right
Steer channel picks up 'trim' on startup
Activ. stick left/right <1s = L/R on/off
Activ. stick left >2s = Hazards on/off
Activ. stick right >2s = Flasher on/off

3 flash = 'P' outputs 1-8 flash = P1-8 7 flash = On/Off led 1-7 flash = Channel 1-7 1 flash = 'high' stick >2s on/off
2 flash = 'high' stick <1s on/off
3 flash = 'low' stick >2s on/off
4 flash = 'low' stick <1s on/off
35712

36713
1 channel controls 1-4 outputs
Outputs 'toggle' on/off

3 flash = 'P' outputs 1-8 flash = P1-8 8 flash = On/Off led 1-7 flash = Channel 1-7 1 flash = 'low' stick on
2 flash = 'high' stick on
1 channel controls 1-2 outputs
'Center' = off

4 flash = Other settings 1 flash = 'Other 1' 1 flash = Arming: Disabled
2 flash = Arming: Low stick
3 flash = Arming: Middle stick
1-7 flash = Arming Ch 1-7 1 flash = LVC Disabled
2 flash = LVC Enabled
41332

4 flash = Other settings 2 flash = 'Other 2' 1 flash = LED2 Disabled
2 flash = LED2 Enabled
1-8 flash = LED2 Pad P1-8 1 flash = No reset
2 flash = FACTORY RESET
42251 LED2: use a Pad number that is driving any Led
LED2: 'disable' if all outputs are servos
Factory Reset = Restore Defaults




3. DX3:

1. Use full 'brake' to make receiver enter programming mode on startup.
2. Use 3-position Aux channel to make yes/no choices.

Home ¦ Videos ¦ About ¦ Buy ¦ Email